Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle F8E1 Error Fix: Low Water Flow / Water Supply Error

The washer is not detecting adequate water flow into the tub within the allowed fill time. Check that both hot and cold water supply faucets behind the washer are fully open. Inspect the water inlet hoses for kinks. Remove the hoses from the back of the washer and clean the small mesh inlet screens at the water inlet valve — mineral buildup and sediment are the most common cause. Verify household water pressure is adequate (20-120 PSI required). If the screens and supply are clear, test the water inlet valve solenoids with a multimeter — each coil should read 500-1500 ohms. Replace the inlet valve if a solenoid is open.

Medium severity2 fixes available✨ Free fix available

Quick Answer

Error F8E1 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Low Water Flow / Water Supply Error. The top-ranked community fix is “Test and Replace Water Inlet Valve Solenoids” (hard difficulty, ~60 min, DIY cost: $10-$20). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · washer

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many washer repairs can be done safely at home, consider hiring a qualified technician if:

The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $120-$180.

Other Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error Codes

Door Lock Failure

2 fixes

F0E2

Overloaded or Excessive Suds

2 fixes

F0E5

Off-Balance Load Detected

2 fixes

F1E1

Main Control EEPROM Error

2 fixes

F1E2

Motor Control Unit Error

2 fixes

F3E1

Pressure Switch / Water Level Sensor Error

2 fixes

F3E2

Water Temperature Sensor Fault

2 fixes

F5E1

Door Switch Error

2 fixes

People Also Ask About Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error F8E1

What does error code F8E1 mean on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

Error code F8E1 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Low Water Flow / Water Supply Error. The washer is not detecting adequate water flow into the tub within the allowed fill time. Check that both hot and cold water supply faucets behind the washer are fully open. Inspect the water inlet hoses for kinks. Remove the hoses from the back of the washer and clean the small mesh inlet screens at the water inlet valve — mineral buildup and sediment are the most common cause. Verify household water pressure is adequate (20-120 PSI required). If the screens and supply are clear, test the water inlet valve solenoids with a multimeter — each coil should read 500-1500 ohms. Replace the inlet valve if a solenoid is open.

How do I fix error code F8E1 on my Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

The most successful fix is "Test and Replace Water Inlet Valve Solenoids" (hard difficulty, ~60 minutes). Estimated DIY cost: $10-$20. HomeMD has 2 community-ranked fixes for this error.

Is error code F8E1 on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle serious?

This error is rated medium severity. It should be addressed soon, but your appliance may still function in a limited capacity.

Can I fix Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F8E1 myself?

Yes — the top-ranked community fix ("Test and Replace Water Inlet Valve Solenoids") is rated hard difficulty and takes about 60 minutes. Tools needed: Phillips screwdriver, Multimeter, Adjustable pliers.

How much does it cost to repair Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F8E1?

DIY cost: $10-$20. Professional repair typically costs $120-$180. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes, including: dL (Door Lock Failure), F0E2 (Overloaded or Excessive Suds), F0E5 (Off-Balance Load Detected), F1E1 (Main Control EEPROM Error), F1E2 (Motor Control Unit Error), and 3 more.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes:

dL — Door Lock Failure (2 fixes)
F0E2 — Overloaded or Excessive Suds (2 fixes)
F0E5 — Off-Balance Load Detected (2 fixes)
F1E1 — Main Control EEPROM Error (2 fixes)
F1E2 — Motor Control Unit Error (2 fixes)
F3E1 — Pressure Switch / Water Level Sensor Error (2 fixes)
F3E2 — Water Temperature Sensor Fault (2 fixes)
F5E1 — Door Switch Error (2 fixes)

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx