Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle F1E2 Error Fix: Motor Control Unit Error

The main control board cannot communicate with the motor control unit (MCU). The MCU is a separate circuit board that drives the washer motor. Check the wiring harness between the CCU (main control) and the MCU (motor control) for loose connections, broken wires, or corrosion. Inspect both boards for signs of burn marks, damaged components, or water damage. Disconnect power for 1 minute and reset. If the code persists, replace the MCU first, then the CCU if the issue continues.

High severity2 fixes available✨ Free fix available

Quick Answer

Error F1E2 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Motor Control Unit Error. The top-ranked community fix is “Replace the Motor Control Unit (MCU) Circuit Board” (hard difficulty, ~60 min, DIY cost: $15-$25). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · washer

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many washer repairs can be done safely at home, consider hiring a qualified technician if:

This is a high severity error — continued use may cause damage or a safety hazard
The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $200-$300.

Other Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error Codes

Door Lock Failure

2 fixes

F0E2

Overloaded or Excessive Suds

2 fixes

F0E5

Off-Balance Load Detected

2 fixes

F1E1

Main Control EEPROM Error

2 fixes

F3E1

Pressure Switch / Water Level Sensor Error

2 fixes

F3E2

Water Temperature Sensor Fault

Door Switch Error

Door Lock Error

People Also Ask About Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error F1E2

What does error code F1E2 mean on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

Error code F1E2 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Motor Control Unit Error. The main control board cannot communicate with the motor control unit (MCU). The MCU is a separate circuit board that drives the washer motor. Check the wiring harness between the CCU (main control) and the MCU (motor control) for loose connections, broken wires, or corrosion. Inspect both boards for signs of burn marks, damaged components, or water damage. Disconnect power for 1 minute and reset. If the code persists, replace the MCU first, then the CCU if the issue continues.

How do I fix error code F1E2 on my Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

The most successful fix is "Replace the Motor Control Unit (MCU) Circuit Board" (hard difficulty, ~60 minutes). Estimated DIY cost: $15-$25. HomeMD has 2 community-ranked fixes for this error.

Is error code F1E2 on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle serious?

This error is rated high severity. You should address it promptly — continued use could cause damage or safety concerns.

Can I fix Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F1E2 myself?

Yes — the top-ranked community fix ("Replace the Motor Control Unit (MCU) Circuit Board") is rated hard difficulty and takes about 60 minutes. Tools needed: T20 Torx screwdriver, Phillips screwdriver, Multimeter.

How much does it cost to repair Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F1E2?

DIY cost: $15-$25. Professional repair typically costs $200-$300. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes, including: dL (Door Lock Failure), F0E2 (Overloaded or Excessive Suds), F0E5 (Off-Balance Load Detected), F1E1 (Main Control EEPROM Error), F3E1 (Pressure Switch / Water Level Sensor Error), and 3 more.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes:

dL — Door Lock Failure (2 fixes)
F0E2 — Overloaded or Excessive Suds (2 fixes)
F0E5 — Off-Balance Load Detected (2 fixes)
F1E1 — Main Control EEPROM Error (2 fixes)
F3E1 — Pressure Switch / Water Level Sensor Error (2 fixes)
F3E2 — Water Temperature Sensor Fault (2 fixes)
F5E1 — Door Switch Error (2 fixes)
F5E2 — Door Lock Error (2 fixes)

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx