👕Washer

F6E1

Amana · NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle

Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle F6E1 Error Fix: Serial Communication Error

The main control board (CCU) cannot communicate with the user interface (UI) board. This is a serial communication link failure between the two boards. Check the wiring harness ribbon cable connecting the UI board (behind the control panel) to the CCU (on the back of the machine). Look for loose connectors, bent pins, or corrosion. Disconnect power for 1 minute and reconnect. If the code persists, try replacing the UI board first. If the issue continues, the CCU may need replacement.

High severity2 fixes available✨ Free fix available

Quick Answer

Error F6E1 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Serial Communication Error. The top-ranked community fix is “Replace UI Board and Test Communication” (hard difficulty, ~90 min, DIY cost: $50-$80). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · washer

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many washer repairs can be done safely at home, consider hiring a qualified technician if:

This is a high severity error — continued use may cause damage or a safety hazard
The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $200-$300.

Other Amana Models with Error F6E1

NED5800HW 7.0 cu ft Electric Dryer with Wrinkle Prevent and Sensor Dry

dryer · 2 fixes

Other Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error Codes

Door Lock Failure

2 fixes

F0E2

Overloaded or Excessive Suds

2 fixes

F0E5

Off-Balance Load Detected

2 fixes

F1E1

Main Control EEPROM Error

2 fixes

F1E2

Motor Control Unit Error

2 fixes

F3E1

Pressure Switch / Water Level Sensor Error

2 fixes

F3E2

Water Temperature Sensor Fault

2 fixes

F5E1

Door Switch Error

2 fixes

People Also Ask About Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle Error F6E1

What does error code F6E1 mean on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

Error code F6E1 on the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle means: Serial Communication Error. The main control board (CCU) cannot communicate with the user interface (UI) board. This is a serial communication link failure between the two boards. Check the wiring harness ribbon cable connecting the UI board (behind the control panel) to the CCU (on the back of the machine). Look for loose connectors, bent pins, or corrosion. Disconnect power for 1 minute and reconnect. If the code persists, try replacing the UI board first. If the issue continues, the CCU may need replacement.

How do I fix error code F6E1 on my Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle?

The most successful fix is "Replace UI Board and Test Communication" (hard difficulty, ~90 minutes). Estimated DIY cost: $50-$80. HomeMD has 2 community-ranked fixes for this error.

Is error code F6E1 on a Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle serious?

This error is rated high severity. You should address it promptly — continued use could cause damage or safety concerns.

Can I fix Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F6E1 myself?

Yes — the top-ranked community fix ("Replace UI Board and Test Communication") is rated hard difficulty and takes about 90 minutes. Tools needed: T20 Torx screwdriver, Needle-nose pliers.

How much does it cost to repair Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle error F6E1?

DIY cost: $50-$80. Professional repair typically costs $200-$300. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes, including: dL (Door Lock Failure), F0E2 (Overloaded or Excessive Suds), F0E5 (Off-Balance Load Detected), F1E1 (Main Control EEPROM Error), F1E2 (Motor Control Unit Error), and 3 more.

Which other Amana models have the F6E1 error?

Error code F6E1 also appears on 1 other Amana model: NED5800HW 7.0 cu ft Electric Dryer with Wrinkle Prevent and Sensor Dry. The fix may vary by model, so check each model's specific page for tailored repair steps.

What other error codes does the Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle have?

The Amana NFW5800HW 4.3 cu ft Front Load Washer with Steam and Sanitize Cycle has 8 other known error codes:

dL — Door Lock Failure (2 fixes)
F0E2 — Overloaded or Excessive Suds (2 fixes)
F0E5 — Off-Balance Load Detected (2 fixes)
F1E1 — Main Control EEPROM Error (2 fixes)
F1E2 — Motor Control Unit Error (2 fixes)
F3E1 — Pressure Switch / Water Level Sensor Error (2 fixes)
F3E2 — Water Temperature Sensor Fault (2 fixes)
F5E1 — Door Switch Error (2 fixes)

Which other Amana models have the F6E1 error?

Error code F6E1 also appears on 1 other Amana model:

NED5800HW 7.0 cu ft Electric Dryer with Wrinkle Prevent and Sensor Dry (dryer) · 2 fixes

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx