🔥Oven / Range

Hotpoint · RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates

Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates F2 Error Fix: Oven Over-Temperature Condition

The oven temperature has exceeded the safe maximum limit — approximately 615-650°F during normal bake mode or approximately 915-950°F during self-clean cycle; the most common cause is a failed oven temperature sensor (RTD probe) providing an incorrect low reading, which causes the ERC to keep heating; less commonly, a bake or broil relay on the ERC may be welded/fused in the closed position, keeping a heating element energized continuously; check the oven temperature sensor first — measure its resistance with a multimeter at the connector (should be approximately 1,080 ohms at room temperature/70°F and increase linearly as temperature rises); if the sensor reads correctly, the ERC relay has failed and the board needs replacement

Medium severity2 fixes available✨ Free fix available

Quick Answer

Error F2 on the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates means: Oven Over-Temperature Condition. The top-ranked community fix is “Test and Replace Oven Temperature Sensor or ERC Relay” (medium difficulty, ~45 min, DIY cost: $20-$50). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · oven

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many oven repairs can be done safely at home, consider hiring a qualified technician if:

The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $200-$300.

Other Hotpoint Models with Error F2

RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven

oven · 2 fixes

RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking

microwave · 2 fixes

Other Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates Error Codes

Stuck Touch Pad Key

2 fixes

Electronic Oven Control (ERC) Internal Failure

2 fixes

Open Oven Temperature Sensor (RTD Probe)

2 fixes

Shorted Oven Temperature Sensor (RTD Probe)

2 fixes

ERC Relay Board Failure

2 fixes

Stuck Function Key (Bake/Broil/Clean)

2 fixes

Oven Door Lock Motor or Switch Failure

2 fixes

MECH-BURNER

Surface Burner Won't Light or Clicks Continuously

2 fixes

People Also Ask About Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates Error F2

What does error code F2 mean on a Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates?

Error code F2 on the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates means: Oven Over-Temperature Condition. The oven temperature has exceeded the safe maximum limit — approximately 615-650°F during normal bake mode or approximately 915-950°F during self-clean cycle; the most common cause is a failed oven temperature sensor (RTD probe) providing an incorrect low reading, which causes the ERC to keep heating; less commonly, a bake or broil relay on the ERC may be welded/fused in the closed position, keeping a heating element energized continuously; check the oven temperature sensor first — measure its resistance with a multimeter at the connector (should be approximately 1,080 ohms at room temperature/70°F and increase linearly as temperature rises); if the sensor reads correctly, the ERC relay has failed and the board needs replacement

How do I fix error code F2 on my Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates?

The most successful fix is "Test and Replace Oven Temperature Sensor or ERC Relay" (medium difficulty, ~45 minutes). Estimated DIY cost: $20-$50. HomeMD has 2 community-ranked fixes for this error.

Is error code F2 on a Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates serious?

This error is rated medium severity. It should be addressed soon, but your appliance may still function in a limited capacity.

Can I fix Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates error F2 myself?

Yes — the top-ranked community fix ("Test and Replace Oven Temperature Sensor or ERC Relay") is rated medium difficulty and takes about 45 minutes. Tools needed: Multimeter, T20 Torx screwdriver, Needle-nose pliers.

How much does it cost to repair Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates error F2?

DIY cost: $20-$50. Professional repair typically costs $200-$300. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates have?

The Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates has 8 other known error codes, including: F0 (Stuck Touch Pad Key), F1 (Electronic Oven Control (ERC) Internal Failure), F3 (Open Oven Temperature Sensor (RTD Probe)), F4 (Shorted Oven Temperature Sensor (RTD Probe)), F5 (ERC Relay Board Failure), and 3 more.

Which other Hotpoint models have the F2 error?

Error code F2 also appears on 2 other Hotpoint models: RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven, RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking. The fix may vary by model, so check each model's specific page for tailored repair steps.

What other error codes does the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates have?

The Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates has 8 other known error codes:

F0 — Stuck Touch Pad Key (2 fixes)
F1 — Electronic Oven Control (ERC) Internal Failure (2 fixes)
F3 — Open Oven Temperature Sensor (RTD Probe) (2 fixes)
F4 — Shorted Oven Temperature Sensor (RTD Probe) (2 fixes)
F5 — ERC Relay Board Failure (2 fixes)
F7 — Stuck Function Key (Bake/Broil/Clean) (2 fixes)
F9 — Oven Door Lock Motor or Switch Failure (2 fixes)
MECH-BURNER — Surface Burner Won't Light or Clicks Continuously (2 fixes)

Which other Hotpoint models have the F2 error?

Error code F2 also appears on 2 other Hotpoint models:

RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven (oven) · 2 fixes
RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking (microwave) · 2 fixes

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx