🔥Oven / Range

Hotpoint · RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates

Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates F1 Error Fix: Electronic Oven Control (ERC) Internal Failure

The Electronic Range Control (ERC) board has an internal circuit failure — the control board cannot be repaired and must be replaced; disconnect power at the breaker for 60 seconds and restore; if F1 returns immediately, the ERC has a permanent hardware fault; make sure to order the correct ERC for your specific Hotpoint model number as different configurations use different boards even within the same series; the touch pad/keypad can also cause F1 on some models — if the touch pad is a separate component from the ERC, try disconnecting the touch pad ribbon cable from the ERC to isolate whether the fault is in the pad or the board

Medium severity2 fixes available✨ Free fix available

Quick Answer

Error F1 on the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates means: Electronic Oven Control (ERC) Internal Failure. The top-ranked community fix is “Replace the Electronic Range Control (ERC) Board” (hard difficulty, ~60 min, DIY cost: $150-$200). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · oven

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many oven repairs can be done safely at home, consider hiring a qualified technician if:

The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $300-$400.

Other Hotpoint Models with Error F1

RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven

oven · 2 fixes

RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking

microwave · 2 fixes

Other Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates Error Codes

Stuck Touch Pad Key

2 fixes

Oven Over-Temperature Condition

2 fixes

Open Oven Temperature Sensor (RTD Probe)

2 fixes

Shorted Oven Temperature Sensor (RTD Probe)

2 fixes

ERC Relay Board Failure

2 fixes

Stuck Function Key (Bake/Broil/Clean)

2 fixes

Oven Door Lock Motor or Switch Failure

2 fixes

MECH-BURNER

Surface Burner Won't Light or Clicks Continuously

2 fixes

People Also Ask About Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates Error F1

What does error code F1 mean on a Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates?

Error code F1 on the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates means: Electronic Oven Control (ERC) Internal Failure. The Electronic Range Control (ERC) board has an internal circuit failure — the control board cannot be repaired and must be replaced; disconnect power at the breaker for 60 seconds and restore; if F1 returns immediately, the ERC has a permanent hardware fault; make sure to order the correct ERC for your specific Hotpoint model number as different configurations use different boards even within the same series; the touch pad/keypad can also cause F1 on some models — if the touch pad is a separate component from the ERC, try disconnecting the touch pad ribbon cable from the ERC to isolate whether the fault is in the pad or the board

How do I fix error code F1 on my Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates?

The most successful fix is "Replace the Electronic Range Control (ERC) Board" (hard difficulty, ~60 minutes). Estimated DIY cost: $150-$200. HomeMD has 2 community-ranked fixes for this error.

Is error code F1 on a Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates serious?

This error is rated medium severity. It should be addressed soon, but your appliance may still function in a limited capacity.

Can I fix Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates error F1 myself?

Yes — the top-ranked community fix ("Replace the Electronic Range Control (ERC) Board") is rated hard difficulty and takes about 60 minutes. Tools needed: T20 Torx screwdriver, Multimeter, Needle-nose pliers.

How much does it cost to repair Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates error F1?

DIY cost: $150-$200. Professional repair typically costs $300-$400. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates have?

The Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates has 8 other known error codes, including: F0 (Stuck Touch Pad Key), F2 (Oven Over-Temperature Condition), F3 (Open Oven Temperature Sensor (RTD Probe)), F4 (Shorted Oven Temperature Sensor (RTD Probe)), F5 (ERC Relay Board Failure), and 3 more.

Which other Hotpoint models have the F1 error?

Error code F1 also appears on 2 other Hotpoint models: RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven, RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking. The fix may vary by model, so check each model's specific page for tailored repair steps.

What other error codes does the Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates have?

The Hotpoint RGA724EKWH 5.0 cu ft 30 in Gas Range with Sealed Burners and Continuous Grates has 8 other known error codes:

F0 — Stuck Touch Pad Key (2 fixes)
F2 — Oven Over-Temperature Condition (2 fixes)
F3 — Open Oven Temperature Sensor (RTD Probe) (2 fixes)
F4 — Shorted Oven Temperature Sensor (RTD Probe) (2 fixes)
F5 — ERC Relay Board Failure (2 fixes)
F7 — Stuck Function Key (Bake/Broil/Clean) (2 fixes)
F9 — Oven Door Lock Motor or Switch Failure (2 fixes)
MECH-BURNER — Surface Burner Won't Light or Clicks Continuously (2 fixes)

Which other Hotpoint models have the F1 error?

Error code F1 also appears on 2 other Hotpoint models:

RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven (oven) · 2 fixes
RVM5160DHWW 1.6 cu ft Over-the-Range Microwave with 1000 Watts and Sensor Cooking (microwave) · 2 fixes

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx