🔥Oven / Range

MECH-ELEMENT

Hotpoint · RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven

Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven MECH-ELEMENT Error Fix: Bake or Broil Element Burned Out

The bake element (bottom of oven) or broil element (top of oven) has failed — look for a visible break, hole, blister, or bright glowing spot on the element coil; when an element fails, it often has a visible hole or melted spot where it burned through; a burned-out element will show infinite resistance on a multimeter (a good element should read approximately 20-50 ohms); the bake element fails more frequently than the broil element because it is used more; replacement involves removing 2-4 screws holding the element bracket to the rear oven wall, pulling the element forward, disconnecting the push-on wire terminals, and connecting the new element; always verify the replacement element is the correct wattage and physical shape for your Hotpoint model

Medium severity2 fixes available✨ Free fix available

Quick Answer

Error MECH-ELEMENT on the Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven means: Bake or Broil Element Burned Out. The top-ranked community fix is “Replace Burned Out Bake or Broil Element” (medium difficulty, ~45 min, DIY cost: $20-$30). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · oven

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many oven repairs can be done safely at home, consider hiring a qualified technician if:

The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $150-$200.

Other Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven Error Codes

Stuck Touch Pad Key

2 fixes

Electronic Oven Control (ERC) Internal Failure

2 fixes

Oven Over-Temperature Condition

2 fixes

Open Oven Temperature Sensor (RTD Probe)

2 fixes

Shorted Oven Temperature Sensor (RTD Probe)

2 fixes

ERC Relay Board Failure

2 fixes

Stuck Function Key (Bake/Broil/Clean)

2 fixes

Oven Door Lock Motor or Switch Failure

2 fixes

People Also Ask About Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven Error MECH-ELEMENT

What does error code MECH-ELEMENT mean on a Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven?

Error code MECH-ELEMENT on the Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven means: Bake or Broil Element Burned Out. The bake element (bottom of oven) or broil element (top of oven) has failed — look for a visible break, hole, blister, or bright glowing spot on the element coil; when an element fails, it often has a visible hole or melted spot where it burned through; a burned-out element will show infinite resistance on a multimeter (a good element should read approximately 20-50 ohms); the bake element fails more frequently than the broil element because it is used more; replacement involves removing 2-4 screws holding the element bracket to the rear oven wall, pulling the element forward, disconnecting the push-on wire terminals, and connecting the new element; always verify the replacement element is the correct wattage and physical shape for your Hotpoint model

How do I fix error code MECH-ELEMENT on my Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven?

The most successful fix is "Replace Burned Out Bake or Broil Element" (medium difficulty, ~45 minutes). Estimated DIY cost: $20-$30. HomeMD has 2 community-ranked fixes for this error.

Is error code MECH-ELEMENT on a Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven serious?

This error is rated medium severity. It should be addressed soon, but your appliance may still function in a limited capacity.

Can I fix Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven error MECH-ELEMENT myself?

Yes — the top-ranked community fix ("Replace Burned Out Bake or Broil Element") is rated medium difficulty and takes about 45 minutes. Tools needed: Phillips screwdriver, Needle-nose pliers, Non-contact voltage tester, Multimeter.

How much does it cost to repair Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven error MECH-ELEMENT?

DIY cost: $20-$30. Professional repair typically costs $150-$200. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven have?

The Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven has 8 other known error codes, including: F0 (Stuck Touch Pad Key), F1 (Electronic Oven Control (ERC) Internal Failure), F2 (Oven Over-Temperature Condition), F3 (Open Oven Temperature Sensor (RTD Probe)), F4 (Shorted Oven Temperature Sensor (RTD Probe)), and 3 more.

What other error codes does the Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven have?

The Hotpoint RBS360DMWW 5.0 cu ft 30 in Free-Standing Electric Range with Self-Clean Oven has 8 other known error codes:

F0 — Stuck Touch Pad Key (2 fixes)
F1 — Electronic Oven Control (ERC) Internal Failure (2 fixes)
F2 — Oven Over-Temperature Condition (2 fixes)
F3 — Open Oven Temperature Sensor (RTD Probe) (2 fixes)
F4 — Shorted Oven Temperature Sensor (RTD Probe) (2 fixes)
F5 — ERC Relay Board Failure (2 fixes)
F7 — Stuck Function Key (Bake/Broil/Clean) (2 fixes)
F9 — Oven Door Lock Motor or Switch Failure (2 fixes)

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx