👕Washer

F01

Miele · Miele WXD 160 WCS W1 Front-Load Washer

Miele Miele WXD 160 WCS W1 Front-Load Washer F01 Error Fix: NTC Temperature Sensor — Short Circuit

The NTC thermistor measuring wash water temperature has a short circuit (resistance near zero). The control board reads an impossibly high temperature. Check the NTC sensor connector for moisture or corrosion. Measure sensor resistance — a shorted NTC reads near 0 ohms instead of the expected ~50K ohms at 25°C.

warning2 fixes available✨ Free fix available

Quick Answer

Error F01 on the Miele Miele WXD 160 WCS W1 Front-Load Washer means: NTC Temperature Sensor — Short Circuit. The top-ranked community fix is “Test and Replace the NTC Temperature Sensor” (medium difficulty, ~45 min, DIY cost: $15-$25). 2 community-ranked fixes available below.

Published February 2026 · 2 fixes · washer

Content is based on manufacturer service documentation, community repair experience, and OEM technical bulletins. Always verify with your owner's manual.Learn about our editorial standards.

When to Call a Professional

While many washer repairs can be done safely at home, consider hiring a qualified technician if:

The repair involves electrical wiring, gas lines, or refrigerant
You've tried the top-ranked fix and the error persists
You smell gas, see sparking, or notice water leaking
The repair requires specialized tools you don't have
Your appliance is still under manufacturer warranty

Average professional repair cost for this issue: $120-$180.

Other Miele Models with Error F01

Miele TWI 180 WP T1 Heat Pump Dryer with WiFiConn@ct

dryer · 2 fixes

Miele TXD 160 WP T1 Heat Pump Dryer

dryer · 2 fixes

Miele WWH 860 WCS W1 Front-Load Washer with TwinDos

washer · 2 fixes

Other Miele Miele WXD 160 WCS W1 Front-Load Washer Error Codes

CARBON BRUSH WORN

Motor Carbon Brushes Worn

2 fixes

DISPENSER DRAWER LEAK

Detergent Dispenser Drawer Leaking

2 fixes

DOOR SEAL TEAR

Door Boot Gasket Torn or Mouldy

2 fixes

DRAIN PUMP BLOCK

Drain Pump Blocked by Foreign Object

2 fixes

DRUM BEARING WORN

Drum Bearing Assembly Worn

2 fixes

F02

NTC Temperature Sensor — Open Circuit

2 fixes

F03

Pressure Switch Fault

2 fixes

F04

Heating Relay Fault

2 fixes

People Also Ask About Miele Miele WXD 160 WCS W1 Front-Load Washer Error F01

What does error code F01 mean on a Miele Miele WXD 160 WCS W1 Front-Load Washer?

Error code F01 on the Miele Miele WXD 160 WCS W1 Front-Load Washer means: NTC Temperature Sensor — Short Circuit. The NTC thermistor measuring wash water temperature has a short circuit (resistance near zero). The control board reads an impossibly high temperature. Check the NTC sensor connector for moisture or corrosion. Measure sensor resistance — a shorted NTC reads near 0 ohms instead of the expected ~50K ohms at 25°C.

How do I fix error code F01 on my Miele Miele WXD 160 WCS W1 Front-Load Washer?

The most successful fix is "Test and Replace the NTC Temperature Sensor" (medium difficulty, ~45 minutes). Estimated DIY cost: $15-$25. HomeMD has 2 community-ranked fixes for this error.

Is error code F01 on a Miele Miele WXD 160 WCS W1 Front-Load Washer serious?

This error is rated warning severity. It is generally not urgent and can often be resolved with a simple DIY fix.

Can I fix Miele Miele WXD 160 WCS W1 Front-Load Washer error F01 myself?

Yes — the top-ranked community fix ("Test and Replace the NTC Temperature Sensor") is rated medium difficulty and takes about 45 minutes. Tools needed: T20 Torx screwdriver, Multimeter, Needle nose pliers.

How much does it cost to repair Miele Miele WXD 160 WCS W1 Front-Load Washer error F01?

DIY cost: $15-$25. Professional repair typically costs $120-$180. Many homeowners save money by trying the top-ranked community fix first.

What other error codes does the Miele Miele WXD 160 WCS W1 Front-Load Washer have?

The Miele Miele WXD 160 WCS W1 Front-Load Washer has 8 other known error codes, including: CARBON BRUSH WORN (Motor Carbon Brushes Worn), DISPENSER DRAWER LEAK (Detergent Dispenser Drawer Leaking), DOOR SEAL TEAR (Door Boot Gasket Torn or Mouldy), DRAIN PUMP BLOCK (Drain Pump Blocked by Foreign Object), DRUM BEARING WORN (Drum Bearing Assembly Worn), and 3 more.

Which other Miele models have the F01 error?

Error code F01 also appears on 3 other Miele models: Miele TWI 180 WP T1 Heat Pump Dryer with WiFiConn@ct, Miele TXD 160 WP T1 Heat Pump Dryer, Miele WWH 860 WCS W1 Front-Load Washer with TwinDos. The fix may vary by model, so check each model's specific page for tailored repair steps.

What other error codes does the Miele Miele WXD 160 WCS W1 Front-Load Washer have?

The Miele Miele WXD 160 WCS W1 Front-Load Washer has 8 other known error codes:

CARBON BRUSH WORN — Motor Carbon Brushes Worn (2 fixes)
DISPENSER DRAWER LEAK — Detergent Dispenser Drawer Leaking (2 fixes)
DOOR SEAL TEAR — Door Boot Gasket Torn or Mouldy (2 fixes)
DRAIN PUMP BLOCK — Drain Pump Blocked by Foreign Object (2 fixes)
DRUM BEARING WORN — Drum Bearing Assembly Worn (2 fixes)
F02 — NTC Temperature Sensor — Open Circuit (2 fixes)
F03 — Pressure Switch Fault (2 fixes)
F04 — Heating Relay Fault (2 fixes)

Which other Miele models have the F01 error?

Error code F01 also appears on 3 other Miele models:

Miele TWI 180 WP T1 Heat Pump Dryer with WiFiConn@ct (dryer) · 2 fixes
Miele TXD 160 WP T1 Heat Pump Dryer (dryer) · 2 fixes
Miele WWH 860 WCS W1 Front-Load Washer with TwinDos (washer) · 2 fixes

Ad Space — banner

Replace ADSENSE_PUBLISHER_ID in AdUnit.tsx